The word subnetwork (subnet for short) has two related meanings. In the older and more general meaning, it meant one physical network of an internetwork. In the Internet Protocol (IP), a subnetwork (usually known as a subnet ) is a division of a what has also been called classful network. The rest of this article is about the second meaning.

Subnetting an IP network allows you to break down what appears (logically) to be a single large network into smaller ones. It was originally introduced before the introduction of classful network numbers in IPv4, to allow a single site to have a number of local area networks. Even after the introduction of classful network numbers, it continued to be useful, as it reduced the number of entries in the Internet-wide Routing table (by hiding information about all the individual subnets inside a site). As a side benefit, it also resulted in reduced network overhead, by dividing the parts which receive IP broadcasts.

= Network masks =

A network mask, also known as a subnet mask, netmask or address mask, is a mask (computing) used to tell how much of an IP address identifies the Subnetwork the host is on and how much identifies the host.

Subnet masks are usually represented in the same representation used for addresses themselves; in IPv4, dotted quad notation (four numbers from zero to 255 separated by periods, e.g. 255.128.0.0) or, less commonly, as an eight-digit hexadecimal number (e.g. FF.80.00.00 = 255.128.0.0).

A shorter form, which is known as Classless Inter-Domain Routing (CIDR) notation, gives the network number followed by a slash and the number of one bits in the binary notation of the netmask (i.e. the number of relevant bits in the network number). For example, 192.0.2.96/28 indicates an IP address where the first 28 bits are used as the network address (same as 255.255.255.240).

= Subnetworking concept =

IPv4 addresses are broken down into three parts, the network part, the subnet part (now often considered part of the network part, although originally it was part of the rest part) and the host part. There are three classful networkes of IP address which determine how much is which.

Subnetting is the process of allocating bits from the host portion as a network portion. For example, giving the class A network 10.0.0.0 a subnet mask of 255.255.0.0 would break it down into 256 sub-networks (10.0.0.0 to 10.255.0.0). Indicating that the first Octet of the IP address shows the network address, the second one shows the subnet number and the last two show the host part. A Binary and operation of the host address with the subnet mask extracts the complete subnetwork address (see example below).

Subnet masks are not limited to whole octets, either. For example 255.254.0.0 (or /15) is also a valid mask. Applied to a class A address this would create 128 subnetworks in intervals of two (1.2.0.1 - 1.3.255.254, 1.4.0.1 - 1.5.255.254, etc).

== Example ==

Having the IP address 12.11.10.9 with a class A subnet mask of 255.254.0.0 (the same as 12.11.10.9/15) says:

Host address 12.11.10.9 Decimal = 00001100 00001011 00001010 00001001 Binary. The first bit is zero, therefore we have a class A network with the network address 12.0.0.0 (see classful network).

Subnet mask 255.254.0.0 Decimal = 11111111 11111110 00000000 00000000 Binary. The subnet mask extends the network address by 7 more bits (254). Thus we have a subnet number of 10 and an extended network address of 12.10.0.0 (decimal) = 00001100 00001010 00000000 00000000 (binary) (Binary and of 12.11.10.9 with 255.254.0.0).

The remaining host part is 0.1.10.9 Decimal = 00000000 00000001 00001010 00001001 Binary.

Determining the number of hosts and subnets on a particular network is quite easy, if you know the subnet mask. Say you have the network address 204.4.32.0 with a subnet mask of 255.255.224.0. This network address can also be written as 204.4.32.0/19

Network address 204.4.32.0 Decimal = 11001100.00000100.00100000.00000000 Binary

Subnet mask 255.255.224.0 Decimal = 11111111.11111111.11100000.00000000 Binary

The subnet mask has 19 Bits for the network portion of the address, and 13 Bits for the host part.

2^3 = 8 possible subnets available according to [http://www.ietf.org/rfc/rfc1812 RFC 1812], otherwise using the old [http://www.ietf.org/rfc/rfc950 RFC 950] standard the number of usable subnets is 6. This is due to [http://www.ietf.org/rfc/rfc950 RFC 950] not supporting subnets with either all 1 s or all 0 s.

2^{13} - 2 = 8190 possible hosts available to each subnet.

= Nonstandard subnets =

== Subnet zero ==

Technically illegal, but still useable is the extreme first subnetwork. For example, subnet 1.0.0.0 with a subnet address of 255.255.0.0. The problem with this subnet is that the unicast address for the subnet is the same as the unicast address for the entire class A network.

== Interleaved subnets ==

It has been proposed that there might be some advantage (eg. against malicious individuals) in making the network Internet Protocol addresses more unpredictable through the use of a less standard subnet mask. This is done by using subnet masks such as 201.35.98.105 which do not cleanly separate the address into the two sections but instead interleave them. This is to be used by MAGI Technologies Ltd. in their server suite, in conjunction with a Dynamic_Host_Configuration_Protocol server which assigns addresses in a relatively unpredictable manner. It is not yet known whether any Router or network switch will process these addresses. Such technology would also have to be used behind a NAT layer because they do not conform with any address pool assigned by IANA.

== See also == *Longest prefix match *IPv4 subnetting reference *Classless Inter-Domain Routing *Classful network

=External links=